2008 Boart Longyear DB430 Rotary Drill ID: 1206373

2008 Boart Longyear DB430 Rotary Drill

• Make: Boart Longyear
• Model: DB 430
• Type: Rotary Drill
• Hours: 220
• Compressor: None
• Engine: Deutz 4 Cylinder
• Mud Pump: Moyno 3L6 (New 2018, 16' Stroke, Mast is 20')
• Mounted On: Tracks
• Tools/Options: Rotary/Coring Head has been Upgraded to a LF540
• Deck Engine is a 140 HP, 4.7 Liter
• Wireline Winch & a Pullmaster Winch
• Hydraulic Rod Rack with 400' of 2-3/8" API Drill Rod
• Dual Rod Clamps
• Breakout Wrench
  
  
• Specifications:
  • Standard Drilling Systems
    • 4" - 6.5": 300m (985ft)
      
      
  • PRIME MOVER:
    • Standard Unit: DEUTZ BF4M1013EC Diesel Engine
    • Power (maximum): 104kW@ 2200 RPM (140HP @ 2200 RPM)
    • Tank Capacity: 230 L (60 Gallons)
    • Fuel Consumption: 195 Gal/kWh
    • Electrical Circuit: 24 Volt
    • NOTE: The engine has sufficient power to run the rig up to 2500 meters above sea level at 25 °C
      
      
  • ROTARY HEAD DB430 - TORQUE ANO RPM RATINGS
    • Low Gear: 4,600/75 Nm/rpm (33,501/75 lb-ft/rpm)
    • High Gear: 2,300/150 Nm/rpm (1,675/150 lb-ft/rpm)
    • Bore - Inside Diameter: 52mm (2in)
    • Swivel - Inside Diameter: 24mm (1in)
    • Rotation Motors: Danfoss OMT 160
    • Top Drive Flange: 2 3/8 API Reg Box
    • Gear Ratio: 4.047:1
    • Distance from Drilling Line to Chain: 202mm (7.95in)
      
      
  • HYDRAULIC SYSTEM
    • Pump: Variable Load-Sensing with Torque Control
    • Max Flow: 230 Lpm (60GPM)
    • Max Pressure: 280 bar (4,060 PSI)
    • Hydraulic Oil Volume: 160 L (42 Gal)
    • Oil Cooler Capacity: 16kW (21.4HP)
      
      
  • DRILL MAST AND FEED SYSTEM
    • Feed Stroke: 4,000mm (13ft)
    • Feed Speed - Down: 3.9m/min (12.7ft/min)
    • Feed Pressure Control: +/- 350 N (+/- 78 lbf)
    • Fast Feed Speed
      • Up: 40m/min (130 ft/min)
      • Down: 66m/min (215 ft/min)
    • Pull Down Force: 35kN (7,715 lbf)
    • Pull Back Force: 70kN (15,400 lbf)
      
      
  • MAIN WINCH (Mast Top)
    • Pull on Inner Layer(Maximum): 9kN (1,980 lbf)
    • Line Speed: 35m/min (115ft/min)
    • Cable Diameter: 8mm (5/16in)
      
      
  • ROD CLAMPS
    • Maximum Diameter: 220mm (8.7in)
    • Clamping Sizes: 65 to 95mm sf (2.5in to 3.75in sf)
    • Maximum Holding Force: 10kN (22,500 lbf)
    • Break-Out-Cylinder
    • Max Pull: 80kN (17,984 lbf)
    • Max Push: 115kN (25,853 lbf)
    • Break-Out-Tong
    • Min. Rod Size: 66.6mm (2 5/8in)
    • Max. Rod Size: 81.2mm (3 1/5in)
      
      
  • ROD RACK:
    • Capacity - 3" Rods: 60
    • Capacity - 3 1/2" Rods: 45
      
      
  • UNDERCARRIAGE:
    • Driving Speed:
      • Low Gear: 2.5 km/h  (1.55 mph)
      • High Gear: 4.8 km/h  (2.98 mph)
    • Maximum Grade Ability (Low Gear): 60% (~30° Deg) 
    • Rubber Tracks: Standard
      
      
• Location: Western USA

View More Rotary Drills